Spatialworlds blog

Socialsense blog

Spatial literacy Scoop.it

Geographical thinking Scoop.it

Spatial Education and technology Scoop.it

Follow Spatialworlds on Twitter

Email contact

manning@chariot.net.au

**Two areas of mapping we need to work on are the skills of calculating gradient and vertical exaggeration.**

**Hope this helps?**

###
**Vertical Exaggeration**

Vertical
exaggeration simply means that your vertical scale is larger than your
horizontal scale (in the example you could use 1 cm is equal to 1000m for your
vertical scale, while keeping the horizontal scale the same). Vertical
exaggeration is often used if you want to discern subtle topographic features.

To determine the
amount of vertical exaggeration used to construct a profile, simply divide the
real-world units on the horizontal axis by the real-world units on the vertical
axis (both need to be in metres)

Vertical exaggeration formula: VE = (real world units of horizontal
scale) / (real world units of vertical scale).

As an example for a 1:50000 topographic map, we can set the horizontal scale (x axis) of the profile the same as the map.

As an example for a 1:50000 topographic map, we can set the horizontal scale (x axis) of the profile the same as the map.

* Labeling 1 cm units on x axis: 1cm on map =
50000cm in real world = 500m in real world. If we decide to use the same value
for our vertical scale (1cm = 500m for y axis), then there will be a vertical
exaggeration (VE) of (500m / 500m) = 1x or no vertical exaggeration.

* Changing
our y axis scale so that 1cm would represent 250m then we would have 500m/250m
= 2x (read 2 times) vertical exaggeration.

**Another explanation of how to calculate vertical exaggeration?**

**Step 1:**

You basically look at the vertical scale and the horizontal scale and convert them to the same unit of measurement. Metres is usually the best one.

e.g. vertical scale - 1:50m

horizontal scale - 1:100 000 (the horizontal scale would always be in centimetres at first as marked on the map)

Convert them to the same unit of measurement and this would make

vertical scale - 1:50m

horizontal scale - 1: 1000m

**Step 2:**Then you just divide the metres of the horizontal scale by the metres of the vertical scale

1000m divided by 50m = 20

i.e. The vertical exaggeration is

**20**.

Just remember that when you're trying to calculate the vertical exaggeration on a topographic map, it won't always be a whole number so you'll be expected to round it to the nearest one.

###
** ****Calculating a Gradient (Slope)**

http://www.youtube.com/watch?v=ykeCKm9JqSA
(only first 2 minutes)

- Decide on an area for which you want to
calculate the slope (note, it should be an area where the slope direction
does not change; do not cross the top of a hill or the bottom of a
valley).
- Once you have decided on an area of
interest, draw a straight line perpendicular to the contours on the slope.
- Measure the length (run) of the line you
drew and, using the scale of the map, convert that distance to metres.
- Determine the total elevation change
(rise) along the line you drew (subtract the elevation of the lowest
contour used from the elevation of the highest contour used). You do not
need to do any conversions on this measurement, as it is a real-world
- To calculate the gradient of the slope, divide the elevation change (rise) in metres by the distance (run) of the line you drew (after converting it to metres). The angle you calculated is the angle between a horizontal plane and the surface of the hill

**…and another explanation**

Calculate
the difference in height between the two points, then calculate the difference
in length between the 2 points and divide.

So lets say you have a rise of 100m and a run of 1000m. It means the gradient is 100/1000, but the numerator must be 1 so that would equate to 1/10, or 1:10. It means that for every 10m you travel, the height goes up by 1m. Also make sure the rise and run are in the same units. In this case the gradient can be explained as 1 in 10 or 1:10 or 1/10 or 0.10, which means that for every 10 units travelled horizontally, the ground rises (or falls) one unit vertically.

So lets say you have a rise of 100m and a run of 1000m. It means the gradient is 100/1000, but the numerator must be 1 so that would equate to 1/10, or 1:10. It means that for every 10m you travel, the height goes up by 1m. Also make sure the rise and run are in the same units. In this case the gradient can be explained as 1 in 10 or 1:10 or 1/10 or 0.10, which means that for every 10 units travelled horizontally, the ground rises (or falls) one unit vertically.